How to Measure Windows and Doors for Custom Screens: A Complete Guide

Custom screens are only as good as their measurements. A screen that is 5 mm too wide will not fit. A screen that is 5 mm too narrow will leave a gap where insects get in.

The good news: measuring is simple. It takes about five minutes per window, and you only need two tools. The bad news: most people get it wrong on the first try, because they measure the wrong part of the frame.

This guide walks you through the correct process for windows and doors, explains the most common mistakes, and shows you how to confirm your measurements before ordering.

Tools You Need

You do not need much:

  • A metal tape measure. Not a cloth tape — cloth stretches, and a few millimeters matter here.
  • A pen and paper. Or a notes app on your phone.
  • A phone camera. To photograph the measurements in place.

That is it. No laser measures, no special tools.

Before You Measure: Three Questions

Before you pick up the tape measure, answer three questions:

1. Is the screen inside the frame or outside the frame?

  • Inside mount (recessed): The screen sits inside the window opening, flush with the frame. Measure the inside opening.
  • Outside mount (overlay): The screen sits on top of the frame, covering it. Measure the outside edge of the frame.

These two measurements are different, and using the wrong one is the most common cause of custom screen problems. Confirm which type you need before measuring.

2. Is the frame square?

Older windows are rarely perfectly square. Measure the width at the top, middle, and bottom. If the three measurements differ by more than 5 mm, note it — the screen will need to be cut to the smallest measurement.

3. Are there obstructions?

Check for handles, hinges, or window locks that might interfere with the screen. If there are, note their position and send a photo.

How to Measure a Window

Step 1: Measure the width

Measure from the left edge of the frame to the right edge, at three points:

  • Near the top
  • In the middle
  • Near the bottom

Record all three measurements. Use the smallest one.

Step 2: Measure the height

Measure from the top edge of the frame to the bottom edge, at three points:

  • Near the left
  • In the center
  • Near the right

Record all three. Use the smallest one.

Step 3: Take a photo

Place the tape measure against the frame, showing the measurement clearly. Photograph it. Do this for both width and height.

This photo is your proof — if there is any question about the measurement later, the photo resolves it.

Step 4: Note the frame type

Is the frame aluminum, uPVC, or wood? This affects the installation method. Note it down.

How to Measure a Door

Doors follow the same logic, but there are two extra considerations:

1. Measure the full opening, not the door slab

The door slab is the moving part. The opening is the frame around it. For a screen door, you usually need the opening measurement, not the slab measurement.

2. Check the threshold

Measure from the top of the frame to the threshold (the bottom sill). Do not measure to the floor — the threshold adds height.

Door measurement steps:

  1. Measure the width at the top, middle, and bottom of the opening. Use the smallest.
  2. Measure the height at the left, center, and right of the opening. Use the smallest.
  3. Photograph both measurements with the tape in place.
  4. Note the threshold height and any obstructions (handles, locks).

The Most Common Mistakes

These are the mistakes that cause most custom screen problems:

Mistake 1: Measuring the glass, not the frame

The glass is inside the frame. The screen covers the frame. Measure the frame, not the glass.

Mistake 2: Measuring only once

Always measure at three points. A frame that looks square may be 5 mm off, and that matters.

Mistake 3: Using a cloth tape

Cloth tapes stretch. Use a metal tape measure.

Mistake 4: Forgetting the threshold

On doors, measuring to the floor instead of the threshold adds 10–20 mm to the height. The screen will not fit.

Mistake 5: Not photographing the measurement

Photos resolve disputes. Without one, you have no proof of what you measured.

Mistake 6: Rounding

Do not round to the nearest centimeter. Record the exact millimeter. A 2 mm difference can mean a screen that does not fit.

How to Confirm Your Measurements

Before you order, confirm your measurements in three ways:

1. Measure twice

Measure once, then measure again a day later. If the numbers match, you are confident. If they differ, measure a third time.

2. Photograph with the tape visible

Place the tape measure against the frame and photograph it. The photo should clearly show the number on the tape.

3. Send to the manufacturer for confirmation

A good manufacturer will confirm your measurements before production. At MBORMC, we review every order and confirm the fit before cutting. If something looks off, we ask.

This step alone eliminates most custom screen problems.

What to Send Us

When you are ready to order, send us:

  1. Width — in millimeters or inches, exact
  2. Height — in millimeters or inches, exact
  3. Photos — showing the tape measure against the frame
  4. Frame type — aluminum, uPVC, or wood
  5. Mount type — inside or outside
  6. Quantity — how many screens
  7. Any special notes — handles, locks, obstructions

We will confirm the fit and send a quote within 24 hours.

A Quick Reference Table

Measurement Where to measure Common mistake
Window width Frame edge to frame edge (inside or outside) Measuring the glass
Window height Frame top to frame bottom Forgetting the sill
Door width Opening edge to opening edge Measuring the door slab
Door height Frame top to threshold Measuring to the floor

Final Thoughts

Measuring for a custom screen is not difficult. It takes five minutes, two tools, and a bit of care. The most common mistakes are measuring the wrong part of the frame, measuring only once, and not photographing the result.

Follow the steps in this guide, measure at three points, photograph everything, and send it to us for confirmation. That is the entire process.

If you are ready to order a custom screen, send us your measurements on WhatsApp. We will confirm the fit and send a free quote within 24 hours. Every screen is built to your exact specifications — and if the measurement is wrong on our side, we remake it at no cost.

Send Your Measurements →